Signed in as:
filler@godaddy.com
Signed in as:
filler@godaddy.com
This is an all in one kit for contractors & DIYer's.
It has everything you need to complete a repair except a trowel! Contains Concrete cleaner, concrete bonding agent, & concrete patch material! No more tracked up concrete repairs, it is vehicle trafficable and kid proof in 3 to 15 minutes! Its easy anyone can do it
This video is just an introduction to basic concrete leak repairs against the active water flow (Negative Side Repair). There is much more technology available to you at Pro-Seal Products. Be patient, learn, and ask technical if you need more information, we are here for you. More systems and products below, just scro.
Pro-Seal DP-36 Bonding and drying agent stops water migration in situ of concrete.
Pro-Seal 34 single component wet surface or under fluid sealant saturates oakum packing to be placed in leaking joints or cracks. Highly adhesive and elastic Pro-Seal 34 saturated oakum, moves with the joint to maintain water tight seals.
Pro-Seal Oakum packing is saturated with Pro-Seal 34 wet and underwater sealant prior to packing into leaking, joints, cracks and holes.
Pro-Seal PPW 3 minute rapid set grout is for locking in the the Pro-Seal Oakum saturated with Pro-Seal 34 sealant, that is placed and packed into joints, cracks, or holes over Pro-Seal backer rod compressed (+25%).
Pro-Seal PPW 3 minute rapid set grout is for locking in the the Pro-Seal Oakum saturated with Pro-Seal 34 sealant, that is placed and packed into joints, cracks, or holes over Pro-Seal backer rod compressed (+25%).
Required materials for leaking concrete joint repairs: Pro-Seal DP-36 pre-treatment post cutting joint to size.
Pro-Seal closed cell backer rod to be compressed 25% leaving 1.5" to 2" free space minimum .5" wide. Pro-Seal Oakum to be saturated with Pro-Seal 34 underwater single component Caulking. Pro-Seal PPW or Pro-Seal PPWs high density high compressive strength Nano grout. Call technical for guide specifications for our new project or repair site 800 349 7325.
Use the most efficient tool to cut joints or cracks to a 2" depth (nominal) and a minimum of a .5"+ width (nominal +).
Clean all loose debris and bond breaking materials from cut joints, cracks, and holes.
Using a wet vacuum, remove all dust, mud, and finer solid debris.
If the crack, joint, or hole is wet spray it with Pro-Seal DP-36 bonding and drying agent. If the joint is dry or damp wet the area to be repaired with clean tap water to saturation and then apply
Pro-Seal DP-36 bonding drying agent.
Place Pro-Seal Closed Cell Backer Rod such that it is compressed a minimum of 25% leaving 1 inch to 2 inches between the backer rod and the concrete surface.
Saturate Pro-Seal Oakum with
Pro-Seal 34 single component wet and underwater sealant to saturation .
Pro-Seal 34 Saturated Oakum should fill only 50% of the depth of the remaining joint, crack, or hole from from the top of the pro-Seal Backer Rod to the concrete surface.
Mixed properly it should be the consistency of dry potters clay ball or a bread dough ball.
Use Pro-Seal PPW rapid set (3 minutes) for active leaks and Pro-Seal PPWs slow set 910 to 15 Minutes) for damp or dry leak repairs.
Required materials for leaking concrete joint repairs: Pro-Seal DP-36 pre-treatment post cutting joint to size. Closed cell backer rod to be compressed 25% leaving 1.5" to 2" free space minimum .5" wide. Pro-Seal Oakum to be saturated with Pro-Seal 34 underwater single component Caulking. Pro-Seal PPW or Pro-Seal PPWs high density high compressive strength Nano grout. Call technical for guide specifications for our new project or repair site 800 349 7325.
Required materials for leaking concrete joint repairs: Pro-Seal DP-36 pre-treatment post cutting joint to size. Closed cell backer rod to be compressed 25% leaving 1.5" to 2" free space minimum .5" wide. Pro-Seal Oakum to be saturated with Pro-Seal 34 underwater single component Caulking. Pro-Seal PPW or Pro-Seal PPWs high density high compressive strength Nano grout. Call technical for guide specifications for our new project or repair site 800 349 7325.
When waterproofing against waterflow or Negative side waterproofing concrete Use Pro-Seals Aqua series of coatings based upon expectations. Contact technical for advice or guide specifications at information@prosealproducts.com
Pro-Seal AquaFlex is the final finish coat for a negative side repair, (stopping water leak in concrete against the water flow), waterproofing repair on surfaces with anticipated high vibration, settling, or movement.
Pro-Seal AquaCrete is for a negative side repair, (stopping water leak in concrete against the water flow), waterproofing repair on surfaces with anticipated high water ingress pressures.
Pro-Seal PowerPatch is a rapid curing repair material that can be used on wet surfaces or underwater. When surfaces are wet pre-treat with Pro-Seal DP 36 a fluid extractant. the material is designed to structurally repair deep spalls and level very rough surfaces in harsh coating environments.
Pro-Seal PowerPatch flexible is designed to be applied to dry and wet surfaces as well as through standing water if necessary (contact technical 800 349 7325). Pro-Seal PowerPatch Flexible will heel moving cracks and joints in industrial environments within 45 minutes. Pro-Seal PowerPatch Flexible can be packaged in pail kits or in 10 oz. tubes or 20 oz. kits.
Pro-Seal PowerPatch Casting Grade is designed for structural repair of anchoring concrete where dismantling, shut down and stoppages are not practical. pro-Seal PowerPatch Casting Grade cures rapidly to a functional state without costly shut downs. Notice where installation is dangerous always follow Industrial safety guidelines and facility safety guidelines for your project site.
Pro-Seal PowerPatch Injection Grade material is designed to heal cracks in concrete where there are no other reasonable or better options. Contact technical 800 349 7325 for guide specifications for your project.
Pro-Seal Hot Foot Zebra Muscle Barrier Coating. Coat intake pipes or other structures to reduce or stop Zebra Muscle ingress. contact Technical 800 349 7325.
Pro-Seal Aero-Graph repairs worn metal impeller, propeller surfaces, and ball surfaces of balls in ball valves and other difficult to replace equipment.
Customers have questions, you have answers. Display the most frequently asked questions, so everybody benefits.
Pro-Seal ProCure A is a film building moisture trapping curing agent for concrete.
Pro-Seal DRyCrete is a surface dying agent to remove moisture from the surface of concrete to allow earlier coating and painting accesses. Pro-Seal DryCrete may also be used with curing agents when trying to achieve moisture balances over extended curing periods, contact technical 800 349 7325.
Pro-Seal ROC Hard is an easy way to gain a deep glossy finish on a steel finished concrete floor. All that is required, once floor is clean and prepared, is a commercial grade floor scrubber and red, green, and black pads.
Pro-SealProducts.com
Pro-SealCorp 12995 N Oracle Rd STE 362 Tucson, AZ 85739 USA
USA & CAN, 800-349-7325, Int'l +1 206-451-9527
Copyright © 2020 Pro-SealProducts.com - All Rights Reserved.
Email: Information@prosealproducts.com